Based on the requirements of light weight and safty, a lot of research on response characteristics for automobile metal materials under high strain rate was carried out. The research progress of test equipments, test methods, test data processing methods and the constitutive equation to describe the material response characteristics under high strain rates was summarized. The response characteristics, fitting constitutive equations and the microstructure evolution law of high strength steel and 糖心产精国品免费入口*完整版 under high strain rates were concluded. The response characteristics of the typical aluminum alloy and 糖心产精国品免费入口*完整版under high strain rates were introduced and the constitutive equation of describing rheological behavior of aluminum and magnesium alloys which considering the effects of temperature and thermal activation energe was raised. Some suggestions were proposed about test equipment, test methods, development direction of response characteristics of metallic material for automotive under high strain rates.
引用该论文:MA Mingtu,LI Jie,ZHAO Yan,WU Emei. Research Progress of Response Characteristics of Metallic Materials for Automotive under High Strain Rates[J]. Materials for mechancial engineering, 2017, 41(9): 1~13 糖心产精国品免费入口*完整版,糖心产精国品免费入口*完整版,糖心产精国品免费入口*完整版,糖心产精国品免费入口*完整版. 汽车用金属材料在糖心产精国品免费入口*完整版下响应特性的研究进展[J]. 机械工程材料, 2017, 41(9): 1~13
论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
参考文献
【1】MA M G, YI H L, LU H Z. On the lightweight of automobile[J]. Enginerring Science,2009,11(9):20-27.
【11】HATT W K, MARBURG E. Preliminary report on the present state of knowledge concerning impact tests[J]. Process American Society Testing Meterials,1899,1:27-50.
【12】YOUNG T. A course of lectures on natural philosophy and the mechanical arts[M]. London:J. & H. COX, Brothers, 1807:144-148.
【13】HOPKINSON J.Further experiments on the rupture of iron wire[J]. Process Manchestist Literal Philosophy Society.1872, 11:119-121.
【14】HOPKINSON J. On the rupture of an iron wire by a blow[J]. Process Manchestist Literal Philosophy Society,1872, 11:40-45.
【15】DUNN B W. A photographic impact testing machine for measuring the varying intensity of an impulsive force[J]. Journal of Franklin Institute, 1897,145(1):321-348.
【16】HOPKINSON B. The effects of momentary stresses in metals[J]. Proceedings of the Royal Scociety of London, 1904,74:498-506.
【17】HOPKINSON B. A method of measuring the pressure products in the detonation of high explosives or by the impact of bullets[J]. Philosophical Transactions of the Royal Society of London, 1914, 213:437-456.
【18】FEHR O, PARKER E R, DEMICHAEL D J. Measurement of dynamic stress and strain in tensile test specimens[J]. Journal of Applied Mechanics, 1944, 66:65-71.
【19】KOLSKY H. An investigation of the mechanical properties of materials at very high rate of loading[J].Proceeding of Physical Society, 2002, 62(11):676-700.
【20】GILAT A, WU X. Elecated temperature testing with the torsional Hopkinson bar[J]. Experimental Mechanics,1994,34(2):166-170.
【21】FRANTZ C E, FOLLANSBEE P S, HAWLEY R H. New experimental techniques with the Hopkinson pressure bar[J]. Presented at International Conference on High Energy Rate Fabrication,1984, 1:229-236.
【22】LENNON A M, RAMESH K T. A technique measuring the dynamic behavior of materials at high temperatures[J].International Journal of Plasticity,1998,14(12):1279-1292.
【24】Zwick USA. Schnellzerrei maschinen High-speed Tension Machines[R].[S.l.]:[s.n.],1977.
【25】SIGNORET C, POUYET J M, LATAILADE J L. Adaptation of a microcomputer system to a modified SHPB[J].Journal of physics E:Scientific Instruments,1980,13(12):1284-1286.
【26】BENDA Y, KEN X. High strain rate behavior of 糖心产精国品免费入口*完整版s for automotive applications[J]. Ironmarking & Steelmaking, 2003, 30(6):33-42.
【27】XIAO X R. Dynamic tensile testing of plastic materials[J]. Polymer Testing,2008,27(2):164-178.
【28】LI J, FANG X. Stress wave analysis and optical force measurement of servo-hydraulic machine for high strain rate testing[J]. Experimental Mechanics, 2014,54(8):1497-1501.
【29】XIA Y, ZHU J, WANG K,
et al. Design and verification of a strain gauge based load sensor for medium-speed dynamic tests with a hydraulic test machine[J]. International Journal of Impact Engineering, 2016,88:139-152.
【30】LI J, FANG X F. Numerical stress wave analysis in LS-DYNA and force measurement at strain rates up to 1000 s-1
of a high speed tensile machine[J]. Experimental Mechanics, 2014,54(8):1497-1501.
【32】ALEKSANDER K.22th international forum for materials testing:Testing solutions for the automotive industry[R]. Ulm:Zwick, 2013.
【33】JOHNSON G R, COOK W H. A constitutive model and data for metals subjected to large strains, high strain rate and high temperatures[C]//The Seventh International Symposium. Netherlands:IBS, 1983:541-547.
【34】COWPER G R,SYMONDS P S. Strain hardening and strain rate effects in the impact loading of cantilever beams[J]. Small Business Economics, 1957, 31(3):235-263.
【35】SAMANTARAY D, MANDAL S, BORAH U,
et al. A thermo-viscoplastic constitutive model to predict elevated-temperature flow behaviour in a titanium-modified austenitic stainless steel[J]. Materials Science and Engineering A, 2009, 526(1):1-6.
【36】KLEPACZKO J R. A practical stress-strain-strain-rate temperature constitutive relation of the powerform[J]. Journal of Mechanical Working Technology, 1987, 15(2):143-165.
【37】JONAS J,SELLARS C,TEGART W,et al.Strength and structure under hot working condition[J].International Metal Reviews,1969,130(14):1-4.
【38】SHI H,MCLAREN A,SELLARS C,et al.Constitutive equation for high temperature flow stress of aluminum alloys[J]. High Temperature Materials & Processed, 2015, 13(7):210-216.
【39】CADY C M. High Strenght Steel Stamping Design Manual[M]. Michigan:Auto/steel Partnership,1999:7-10.
【40】XU K, WONG C, YAN B,
et al. A high strain rate constitutive model for high strength steels:2003-01-0260[R]. Detroit:SAE, 2003.
【41】ZERILLI F J, AMSTRONG R W. Dislocation mechanica-based constitutive relations for material dynamic calculations[J]. Journal of Applied Physics, 1987, 61(5):1816-1825.
【42】ZHAO Y, MA M T, WAN X M,
et al. The development of data processing software for dynamic tension of materials[C]//Proceedings of The 2nd
International Conference on Advanced High Strength Steel and Press Hardening. Changsha:WSPC, 2015:126-133.
【43】SPEER J G, MATLOCK D K, COOMAN B C D,
et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia, 2003, 51(9):2611-2622.
【44】MILLER R L. Ultrafine-grained microstructure and mechanical properties of alloy steels[J]. Metallurgical Transaction,1972,3(4):905-912.
【46】BHADESHIA H K D H. TRIP-asssited steels[J]. Issij International, 2007,42(9):319-322.
【47】BHADESHIA H K D H. Posco Lectures:The Banite Reaction[EB/OL].[2017-03-15]. https://www.phase-trans.msm.cam.ac.uk/2007/POSCO_Bainite_Notes.pdf?origin=publication_detail.
【48】YI H L, CHEN P, WANG G,
et al. δ-TRIP steel:Physical and mechanical metallurgy[J]. Enginnering Sciences, 2004, 2:14-19.
【49】CHATFIED D A, ROTE R R. Strain rate effects on the properties of high strength low alloy steels:No.740177[R].[S.l.]:[s.n.], 1974.
【50】SHI M, MEULEMAN. Strain rate sensitivity of automotive steels:No. 920245[R].[S.l.]:SAE,1992.
【51】XU K, ARSENAULT K J. High temperature deformation of NiAl matrix composites[J]. Acta Materialia,1999, 47(10):3023-3040.
【52】KANTZ S, BLECK W, PAPAMANTELLOS K. The influence of test temperature on the mechanical properties and formability of cold rolled low and high alloyed TRIP steels[C]//Proceedings of the 20th
Biennial congress。[S.l.]:My Science Work, 1998.
【56】ZHANG J P, FANG G, JIN Q S,
et al. Mechanical properties and microstructure of DP steel sheets under dynamic loads[C]//Proceedings of The 2nd
International Conference on Advanced High Strength Steel and Press Hardening.Changsha:WSPC,2015:217-223.
【57】POSCO. 2011POSCO Global EVI forum:Automotive steel data book[R].[S.l.]. POSCO, 2011:58.
【58】MA M T, CHEN G, MA Y H,
et al.The development and application research of light weight heat treated B-grade bullet proof steel[J]. Engineering,2014,12(5):2-7.
【59】MA M T, CHEN G, MA Y H,
et al.The Development and application research of light weight heat treated C-grade bullet proof steel[J].Advanced Materials Research, 2015,1063(5):21-27.
【60】MA M T, ZHANG J W, ZHANG J P. Numerical analysis on bullet penetration resistance of heat treated lightweight C-grade bullet proof steel plates[J]. Advanced Materials Research, 2015, 1063(5):257-263.
【61】MA M T, ZHANG J W, ZHANG J P. Numerical analysis on the shoot resistance of heat treated lightweight B-grade bullet proof steel plates[J]. Engineering, 2014,12(5):12-20.
【62】CURTZE S, KUOKKALA V T. Dependence of tensile deformation behavior of TWIP steels on stacking fault energy temperature and strain rate[J]. Acta Materialia.2010,58(15):5129-5141.
【63】HSU C H,LEE S C,WANG L L,
et al.The high strain-rate fracture behaviors of gray iron under compressive loading[J]. Materials Chemistry and Physics, 2002,73(2/3):174-178.
【64】SAHU P, CURTZE S, DAS A,
et al.Stability of austenite and quasi-adiabatic heating during high-strain-rate deformation of twinning-induced plasticity steels[J]. Scripta Materialia,2010,62(1):5-8.
【65】SI W H, JI J H, PARK K T. Effects of Al addition on high strain rate deformation of fully austenitic high Mn steels[J]. Materials Science and Engineering A,2011,528(24):7267-7275.
【70】GRASSEL O, KRUGER L,FROMMEYER G,
et al. High strength Fe-Mn-(Al,Si) TRIP/TWIP steels development-properties-application[J]. International Journal of Plasticity, 2000, 16(9):1391-1409.
【71】熊荣刚.TWIP钢在不同应变速率下的应变行为研究[D].上海:上海大学,2008.
【72】REED-HILL R E.The inhomogeneity of plastic deformation[M].Ohio:ASM Metals Park,1971:285-286.
【75】MATLOCK D K,BRÄUTIGAM V E, SPEER J G.Application of the quenching and partitioning(Q&P)process to a medium-carbon, high-Si microalloyed bar steel[J].Materials Science Forum, 2013, 432(2):1089-1094.
【77】WANG X D, ZHONG N, RONG Y H,
et al. Novel ultrahigh-strength nanolath martensitic steel by quenching-partitioning-tempering process[J]. Journal of Materials Research, 2009, 24(1):260-267.
【78】WANG X D, GUO Z H, RONG Y H. Mechanism exploration of an ultrahigh strength steel by quenching-partitioning-tempering process[J]. Materials Science and Engineering A, 2011, 529(1):35-40.
【79】CABALLERO F G, BHADESHIA H K D H, MAWELLA K J A,
et al. Very strong low temperature bainite[J]. Materials Science and Technology, 2002, 18(3):279-284.
【80】BHADESHIA H K D H. High performance bainitic steels[J]. Materials Science Forum, 2005, 500/501:63-74.
【81】GARCIA-MATEO C, CABALLERO F G, BHADESHIA H K D H. Mechanical properties of low-temperature bainite[J]. Materials Science Forum, 2005, 500/501:495-502.
【84】PYCHMINTSEV I Y, SAVRAL R A, COOMAN B C D,
et al. International Conference On TRIP-Aided High Strength Ferrous Alloys[C]. Belgium:Ghent, 2002:299-302.
【86】WEI X C, LI L, FU R Y,
et al. On the tensile mechanical property of Si-Mn TRIP Steels at high strain rate[J]. Acta Metallurgica Sinica (English Letters),2002,15(3):285-294.
【87】WEI X C, FU R Y, LI L. Tensile deformation behavior of cold-rolled TRIP-aided steels over large range of strain rates[J]. Materials Science and Engineering A, 2007, 465(1):260-266.
【88】LIU W H,HE Z T,CHEN Y Q,
et al. Dynamic mechanical properties and constitutive equations of 2519A aluminum alloy[J]. Transactions of Nonferrous Metal Society of China, 2014, 24(7):2179-2186.
【90】SMERD R, WINKLER S, SALISBURY C,
et al. High strain rate tensile testing of automotive aluminum alloy sheet[J]. International Journal of Impact Engineering, 2005,32(1):541-560.
【91】LINDHOLM U S, BESSEY R L, SMITH G V. Effects of strain rate on yield strength, tensile strength and elongation of three aluminum alloys[J]. Journal Material, 1971, 6(1):119-133.
【92】OOSTERKAMP L, IVANKOVIC A, VENIZELOS G.High strain rate properties of the selected 糖心产精国品免费入口*完整版s[J]. Material Science & Engeering A, 2000, 278(1/2):225-235.
【93】AVEDSIAN M M, BAKER H. ASM specialty handbook:Magnesium and magnesium alloys[M]. Materials Park:ASM International, 1999:1-11.
【94】LI N. Workshop on China-America automotive materials:Design and manufacture of magnisym compontents for autompbile application[R]. Detroit:[s.n.], 2003.
【95】KIM C H. POSCO Globle EVI forum:POSCO magnesium business[R].[S.l.]:POSCO, 2008.
【96】YU H, YU H S, KIM Y M,
et al. Hot deformation behavior and process maps of Mg-Zn-Cu-Zr magnesium alloy[J].Transactions of Nonferrous Metals Society of China, 2013, 23(3):756-764.
【97】GALIYEV A, KAIBYSHEV R, GOTTSTEIN G. Correlation of plastic deformation and dynamic recrystallization in 糖心产精国品免费入口*完整版ZK60[J]. Acta Materialia, 2001, 49(7):1199-1207.
【98】GALIYEV A, SITDIKOV O, KAIBYSHEV R. Deformation behavior and controlling mechanisms for plastic flow of magnesium and magnesium alloy[J]. Materials Transactions, 2003, 44(4):426-435.
【99】YANG Y Q, LI B C, ZHANG Z M. Flow stress of wrought magnesium alloys during hot compression deformation at medium and high temperatures[J]. Materials Science and Engineering A, 2009, 499(1/2):238-241.
【100】WU Y Z, YAN H G, ZHU S Q,
et al. Flow behavior and microstructure of ZK60 糖心产精国品免费入口*完整版compressed at high strain rate[J].Transaction of Nonferrous Metals Society of China, 2014,24(4):930-939.
【103】SAKAI T, JONAS J J. Overview no. 35 dynamic recrystallization:Mechanical and microstructural considerations[J]. Acta Metallurgica,1984,32(2):189-209.